2002 Miata with 2000 LS1 and T56
#1
V8 Miata Fan
Thread Starter
2002 Miata with 2000 LS1 and T56
Started my marathon in November 2014. Should finish by the end of the month. I've gotten a lot of information from all of you on the site. Just wanted to share some current photos of my build.
The following users liked this post:
02-VIVID (03-19-2018)
The following users liked this post:
02-VIVID (03-19-2018)
#5
V8 Miata Fan
Thread Starter
#7
V8 Miata Fan
Thread Starter
I may have put 100 miles on the car and now my ebay transmission is having problems shifting in and out of 3rd and 4th gear. I pulled transmission this past weekend and shipped it to Tick performance for a rebuild.
#8
V8 Miata Enthusiast
Same thing happened to me.
Bought a salvage T56 and it worked for a couple of months before the 4th gear syncro went out.
What does it cost to have a rebuild at Tick Performance?
I used Texas Drive Train Performance and it cost $1500 to rebuild and upgrade to Viper specs.
Pretty neat cause I got to spend 5 or 6 hours watching him actually do the rebuild.
Bought a salvage T56 and it worked for a couple of months before the 4th gear syncro went out.
What does it cost to have a rebuild at Tick Performance?
I used Texas Drive Train Performance and it cost $1500 to rebuild and upgrade to Viper specs.
Pretty neat cause I got to spend 5 or 6 hours watching him actually do the rebuild.
#9
V8 Miata Fan
Thread Starter
Same thing happened to me.
Bought a salvage T56 and it worked for a couple of months before the 4th gear syncro went out.
What does it cost to have a rebuild at Tick Performance?
I used Texas Drive Train Performance and it cost $1500 to rebuild and upgrade to Viper specs.
Pretty neat cause I got to spend 5 or 6 hours watching him actually do the rebuild.
Bought a salvage T56 and it worked for a couple of months before the 4th gear syncro went out.
What does it cost to have a rebuild at Tick Performance?
I used Texas Drive Train Performance and it cost $1500 to rebuild and upgrade to Viper specs.
Pretty neat cause I got to spend 5 or 6 hours watching him actually do the rebuild.
#10
V8 Miata Fan
Thread Starter
Tick was really backed up on transmission rebuilds. Just got it back today. It's in the car and I'm in the process of getting the driveshaft, exhaust, console, etc. done. Should be able to drive it tomorrow. Transmission should have been a boat anchor. Tick said it had been driven hard. My cases were good but not much else.
#12
V8 Miata Fan
Thread Starter
Wanted to thank Martin Wilson at Monster Miata. I used the following parts from him for my build:
Keith
- K-member and motor mounts
- Transmission Mount
- Axles
- Hubs
- 8.8 weld in differential mount
- clutch master cylinder
- Sway bar mounts
- Oil pan
- Fans
Keith
Last edited by 02-VIVID; 05-15-2018 at 05:06 PM. Reason: Additional parts
#13
V8 Miata Enthusiast
Another thread reminded me that I do have a question for you.
It is my understanding that Martin's front subframe locates the engine further forward than the V8 Roadster subframe.
Was it far enough forward for you that the tunnel did not need to be cut and re-welded?
It is my understanding that Martin's front subframe locates the engine further forward than the V8 Roadster subframe.
Was it far enough forward for you that the tunnel did not need to be cut and re-welded?
#14
V8 Miata Fan
Thread Starter
I didn't do any cutting or welding on the tunnel. I did have to use a big hammer to clearance it some, but it wasn't drastic. However, I cannot remove bell housing with engine in the car. If you want to be able to replace the clutch without removing the engine then more work to the tunnel would have to be done.
Last edited by 02-VIVID; 07-02-2018 at 05:34 PM.
#15
V8 Miata Enthusiast
Something else I have been meaning to ask.
What roll bars are you running?
The don't look to be Hard Dog Deuces but I think they look better with the extra width.
What roll bars are you running?
The don't look to be Hard Dog Deuces but I think they look better with the extra width.
#16
V8 Miata Fan
Thread Starter
It's a Boss Frog. I liked the way they looked, but when I went to buy one Boss Frog was out of business. I found mine used on craigslist and then had it powder coated silver.
The following users liked this post:
02-VIVID (07-10-2018)
#18
V8 Miata Fan
Thread Starter
My ebay motor hasn't ever run right since I put it in the car. My son has HP tuners software, so we downloaded the tune. Turns out that the previous owner had it tuned for open loop. I got it re-tuned last week. I cannot believe how well the car is running now. It's so much fun to drive now and performs like I thought it should have from the start. I haven't had it on the dyno yet.
Thread
Thread Starter
Forum
Replies
Last Post
Vorshlag-Fair
General Motors V8 Miata Build Threads
51
05-15-2016 12:32 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)