|
Canadian Monster Miata SN95 Build
13 Attachment(s)
Hi guys I've been a long time reader of this forum but now I think its time for me to start a build thread of my own. The car is a 1990 with 185,000km, I have done some light mods to the car but the drive train is stock.
https://www.v8miata.net/attachment.p...ine=1450895460 A few weeks back I found some FFR axles and an 8.8 thunderbird diff with limited slip and 3.27 gears on craigslist which I picked up to start the project rolling. http://i410.photobucket.com/albums/p...ps05oim1vh.jpg Today I picked up a wrecked SN95 with a T5 from a local scrap car guy. The engine and trans were apparently built for boost. I'm hoping to part out some of the car to make some money back but we will see what I can get rid of. https://www.v8miata.net/attachment.p...ine=1450895460 I'm a fairly capable fabricator and work part time in a machine shop while attending university for mechanical engineering, over the next couple months there will likely be very few updates due to my busy schedule but I hope to dive into this project fully in January 2016. I'll be using martins hubs and thinking about using his subframe, oil pan and headers to save me a bunch of time and effort. The 8.8 I will mount myself similar to some methods I've found online. If anybody has any tips / comments / suggestions about the build or the SN95 working with the martin subframe etc it would be greatly appreciated. Thanks a lot guys I'm looking forward to getting to know the community!! |
The Best of luck with your build!. I looks like you a definitely headed in the traditional direction with proven equipment....Hope you make good progress before winter. Stay warm
|
Welcome and good luck!
|
6 Attachment(s)
Quick update for the build since I haven't added anything since late September.
I harvested the engine and transmission from the parts mustang and sold the body to someone who wanted it for the rear end and front spindles. Spent a while talking to Martin and eventually placed the order for sub frame, hubs, oil pan, headers and engine mounts. https://www.v8miata.net/attachment.p...ine=1450896637 Since then I've advertised and sold my 1.6 engine, trans and diff. The car is basically just a shell right now waiting for the new parts. I have also ordered BC Racing coilovers with custom 670lb front, 450lb rear spring rates. Also recently picked up a set of fixed back racing seats. https://www.v8miata.net/attachment.p...ine=1450896637 The Martin parts arrived about three weeks ago and now that I'm finished school for the next four months I'll be diving into this project, starting with cutting out the engine bay corners and doing some transmission tunnel bashing. I will also be converting the longer bellhousing'd SN95 T5 to work with the stock miata slave, if anybody has any tips on doing this (not sure how many people really go with that longer bellhousing) it would be appreciated. I've seen people use other master / slaves but I don't see why I wouldn't be able to work with the stock miata parts as long as I get the slave in the right place so it has a long enough throw. |
Looks like you've got a great start to the project, I don't know much about the ford conversions so I can't help you with the bellhousing issue. How far along are you with the ME degree?
|
Great start for sure.
You're going to be spending some time trying to make that larger bellhousing fit. I would try to find a used foxbody bell. Find Miata Mike's SN95 build for more details. I think all you need is the fox bell and an adaptor plate due to the longer input shaft. Please post lots. It's going to be a boring winter for me with mine away till spring. edited to add: In the meantime if you come across a deal on a US model washer bottle, grab it- the larger Can. spec one will get in the way of the intake tract. |
Originally Posted by MX-Brad
(Post 18801)
In the meantime if you come across a deal on a US model washer bottle, grab it- the larger Can. spec one will get in the way of the intake tract.
Carry on ! |
stng_96
How far along are you with the ME degree? MX-Brad, Thanks for the tip, I'll keep an eye out for both a US spec washer bottle and fox bell, I have seen Miata Mikes build where he swaped to the fox one but we'll see how much hammering I'm willing to do before I give up! |
Good deal man, I am a Mechanical Engineer also. I know its tough, but keep up the hard work and it will all be worth it!!
|
14 Attachment(s)
Got a fair amount of stuff done today. Started off with pulling the old power steering rack and proceeded to clean it up (it was very greasy). I will be depowering the rack for this build, so I removed all of the old lines from it for now.
https://www.v8miata.net/attachment.p...ine=1451369272 Next I pulled apart the front suspension and dropped the stock subframe. Moved a few brake and fuel lines out of the way before starting to enlarge the bay for the new engine. What I have decided to attempt here is instead of cutting out the corners and leaving them open (I don't have a welder in my garage to weld in any plates, rear subframe etc will be welded elsewhere) I'm going to try and hammer the back corners of the bay into shape. I like the idea of doing this because all the metal is still more or less in tact and may be a bit sturdier than cutting, at least without adding new welded plates. Here are a couple pictures of the initial shaping of the back corners. https://www.v8miata.net/attachment.p...ine=1451369272 https://www.v8miata.net/attachment.p...ine=1451369272 Following this initial clearancing I bolted on the martin subframe and tried to wiggle the engine in to see the problem areas. Quite a nice sight, even if its not fully in place. https://www.v8miata.net/attachment.p...ine=1451369272 It looks to me like I'm going to need to hammer the top of the tunnel a bit so I can slide the trans back just a bit farther so the oil pan can slide back enough to not be sitting on the subframe, right now the pan sits about 1" onto the subframe before the cutout on the pan. Both transmission tunnel sides look like they will need to expand about 3/4" to 1" on each side once the bell housing moves a bit farther back, I think its currently approx 2" forward from final resting position. https://www.v8miata.net/attachment.p...ine=1451369272 https://www.v8miata.net/attachment.p...ine=1451369272 https://www.v8miata.net/attachment.p...ine=1451369272 |
Good Grief, engine setting almost in place in a day? Perhaps I am doing this all wrong.....
|
Haha wow that's quick work! I'm 6 months in and hoping to do my first engine mock up today. Great work! I like the idea of shaping those corners instead of cutting.
|
You're really moving along.
Interesting idea bending the corners. You need evey milimeter of room you can get in that area. I guess if it doesn't work out you can still cut them and get someone to come over with a small flux core welder to button up the corners (or glue them like some folks do). Hopefully you'll be ok as is. Keep up the great progress. |
I do actually have a flux core welder but I really dislike using it in comparison to gas, I guess that's always an option though depending on how tight it gets in there. I'm thinking my main clearance issues will be around the perimeter of the transmission tunnel but hopefully its not too horrible..
|
You think you'll have to cut the tunnel, or will bashing be sufficient? Keep your exhaust routing in mind regarding where your clutch slave ends up. You'll want to be able to bleed and adjust it without removing exhaust.
|
Hoping that a lot of bashing will be good enough but I wont know for a bit. That's a good tip on the slave actually as I think it might be in a slightly lower position on the SN95 bell when compared to a fox, Thanks!!
|
11 Attachment(s)
Got another afternoon in on the car today, very happy with the outcome!
Pulled the engine back out and did some more work with the BFH, stuck the engine in and back out a couple more times marking areas to attack further with the hammer. First pic here is before I hammered the vertical face of the firewall back a bit. https://www.v8miata.net/attachment.p...ine=1451718448 Realizing that wasnt enough, I pushed the vertical part of the firewall back a bit and then managed to wiggle the engine into place on its mounts. Right now the engine is at the most forward point on the slots, I'd like to get it at least a 1/2" farther back for weight / rad clearance. Only thing stopping the engine from going back right now is the driver side cyl head is hitting my hammered back engine bay corner. I'm going to hit that a bunch more tomorrow and possibly whip out the zip disc to chop it back a bit, pleanty of room on the passenger side as well as what appears to be enough room around the bell for it to move back a fair bit. https://www.v8miata.net/attachment.p...ine=1451718448 Here are some photos of clearance around the bell, and again this is the larger SN95 bell, actually in place with room to spare!! https://www.v8miata.net/attachment.p...ine=1451718448 https://www.v8miata.net/attachment.p...ine=1451718448 https://www.v8miata.net/attachment.p...ine=1451718448 This piece of the bell is actually very close to touching the subframe and would probably vibrate against it when running, I'm just going to knick a small bit of it out for clearance. https://www.v8miata.net/attachment.p...ine=1451718448 And the rest of the room around the larger bell https://www.v8miata.net/attachment.p...ine=1451718448 https://www.v8miata.net/attachment.p...ine=1451718448 https://www.v8miata.net/attachment.p...ine=1451718448 https://www.v8miata.net/attachment.p...ine=1451718448 Look at it sitting in there so nicely after all that hammering https://www.v8miata.net/attachment.p...ine=1451718448 |
Another ME here. I too am using sn95 bell and tranny and have everything mocked into place. I think there is plenty of room and don't see any reason for a fox bell. The shifter is also almost in the perfect spot with this set up
|
Really nice work and information...keep us posted
|
19 Attachment(s)
Sorry for the lack of updates lately guys, I've been working on the car pretty much every day after work so not a lot of free time!
First thing I did was pull the steering rack apart and cut the seal off for manual conversion. https://www.v8miata.net/attachment.p...ine=1453361787 Next I decided it would be a good idea to TIG up the flex joint part to eliminate any excess play. https://www.v8miata.net/attachment.p...ine=1453361787 Then reassembled the rack with grease and sealed off all the old power steering fluid fittings. https://www.v8miata.net/attachment.p...ine=1453361787 Before I pulled the engine and trans again I tossed the shifter together with the console and boot, it was perfect! I have a PRO 5.0 shifter and powerstick handle or something that came with the trans. The shifter is a two piece bolted together, I just flipped the side the upper half was attached to and it lined up very well. https://www.v8miata.net/attachment.p...ine=1453361787 Did a little more bashing and then re-routed the lines up the firewall. Then repainted the rear of the engine bay. https://www.v8miata.net/attachment.p...ine=1453361787 https://www.v8miata.net/attachment.p...ine=1453361787 Repainted the engine while it was out, satin black. didnt do anything with the valve covers yet as they need to be repainted once I'm done pulling the engine in and out all the time. https://www.v8miata.net/attachment.p...ine=1453361787 Next I started work on the rear diff. I found some rough dimensions for a design I've seen used here a bit and one which I like for the simplicity. I have re-drawn all the parts to mount the 8.8 diff which you can see me working off here. https://www.v8miata.net/attachment.p...ine=1453361787 https://www.v8miata.net/attachment.p...ine=1453361787 https://www.v8miata.net/attachment.p...ine=1453361787 https://www.v8miata.net/attachment.p...ine=1453361787 https://www.v8miata.net/attachment.p...ine=1453361787 https://www.v8miata.net/attachment.p...ine=1453361787 https://www.v8miata.net/attachment.p...ine=1453361787 https://www.v8miata.net/attachment.p...ine=1453361787 Making all the parts to mount the diff probably took me 4 hours and $15 in steel. Last night I bolted it to the diff to see how it fit, I am using the energy suspension 4.1126 poly bushings. https://www.v8miata.net/attachment.p...ine=1453361787 Tonight I pulled the subframe into a place where I could lay it down (garage is pretty crowded with parts these days). Looks like it will fit great! The parts dropped right into place. https://www.v8miata.net/attachment.p...ine=1453361787 https://www.v8miata.net/attachment.p...ine=1453361787 https://www.v8miata.net/attachment.p...ine=1453361787 And that's all for now guys, hopefully this weekend I'll get it welded up. A question possibly for the moderators: after I can confirm the fitment of these diff mount parts, is there somewhere I could post the PDF drawing files of all the components? I think everyone should have access to these plans if they wish to use this design, I'm also working on a transmission brace which will have detailed plans as well. |
Nice drawings on the diff mount parts, but I do have one concern. I just finished up my diff mount and it looks like everything you used is thinner than mine, or Mike Moninger who originally made that design. For example, that square tubing you used looks like it is 1/8" wall thickness, with the amount of torque those mounts could have to stand up to, I'd be a little concerned that they might twist on you.
|
Miles, if the mods don't come up with something here, I'd be happy to include those pdf's on my blog, with appropriate credit.
I see you're in the mechanical engineering field, is there any way to do some sort of strength and materials analysis of this design? I put these things together based on intuition mostly and observation of what the factories do, but there isn't a lot of science to back them up. Also, there are gussets that are not readily visible that run from side to side both on the front "crossmember" and the rear that I included but did not document well. Very nice work and looking forward to seeing the finished product on the road. Mike |
He should be able to do a Finite element analysis on these pieces, I'd be curious to see the results.
|
3 Attachment(s)
stng_96, I had actually hoped to use 0.1875 wall tubing for those components originally but when I went to the local metal supermarkets thats just what I ended up with. I was thinking it would be fine considering most of the subframe is material of about that thickness, but then you got me thinking.
I've made some assumptions for a "worst case" scenario but if anyone sees any issues with them let me know. I assumed that in a few years my car might be putting out 400lbft of torque to the driveshaft, and that during a launch at peak torque the diff mounts will be subjected to the full 400lbft for a brief instant before the car begins rolling. Also ignored the fact the rear mounts will take load - for a worst case we can assume the rear mounts are taking zero of the resultant torque. Assumed any unusual force spikes would be damped out with the poly bushings. Diff mounts are approx 3.5" away from the input shaft centerline. https://www.v8miata.net/attachment.p...ine=1453451979 So peak force in each square mount is roughly 685 pounds of force at launch, this is ignoring diff and driveshaft weight but I think for the purposes of this analysis it can be negligible. Next I did an FEA analysis on the 0.125 wall plain steel mount. https://www.v8miata.net/attachment.p...ine=1453451979 the 0.125 wall mount had a factor of safely of 21 before any yielding occurred. Next I analised the same mount but with a 0.1875 wall instead https://www.v8miata.net/attachment.p...ine=1453451979 The 0.1875 wall mount had a factor of safely of 30, roughly a 30% increase over the 0.125 wall mount. Quite an increase but I feel comfortable with a factor of safety of 20 in that part, I think the welds will fail in tension on that mount before one buckles in compression. What do you guys think? Mike, I had no idea you were the original creator of that mount, I apologize for not giving you credit earlier. I will talk to you shortly about getting your name on those drawings as well and then sending them over to you. Sorry if there are some grammatical errors in this post or its lacking crucial info, its late, my session timed out and I lost everything, so I've re-written this thing twice! |
That all looks reasonable, with the assumption that you're launching in high gear. You need to factor in the torque multiplication of the transmission, typically around 3:1 in first gear. But it's still a workable design. Especially since the rear mount plays an important part.
To give you some more food for thought, what about the additional load imparted by the transfer of torque thru the axle? At that point, the multiplication by the rear end ratio comes into play, so assuming another 3.5 or so, you could end up with .... um..., a pretty big number that the rear end housing has to deal with. If it could be effectively transmitted to the ground, you could do wheelies in your Miata. As far as credit for the design, that was not the implication. I meant that I would credit YOU for the effort involved in creating the documentation. And now for the analysis. I have always admired the open source concept as applied to projects like putting V8s in Miatas and hopefully now others down the line will benefit from our contributions. So, again, thanks. Mike |
| All times are GMT -5. The time now is 07:15 PM. |
© 2024 MH Sub I, LLC dba Internet Brands