Shawn's Turbo built LQ4
Welp, ive been here long enough, the build has gone through many different phases........ started with a bare tub to pretty much a full blown racecar.
Majority of the build is on youtube @speedhouse So continuing along........ bout to go to the moon. fresh rebuild: forged rods and pistons with arp2000 rod bolts balanced rotating assembly all new bearings rings .030 over high pressure high volume pump arp headstuds sloppy best cam comp springs btr hardened pushrods trunnion kit ls9 mls gaskets all brand new gaskets to seal everything holley pan with trap door baffle ls6 intake, stock truck throttle body, ebay rails regulator lines and fittings everywhere also added 2 oil coolers and still need to plumb in the accusump poor mans rebuild on a tr6060 and converting it to a t56 magnum time to let er eat..... gonna keep it conservative around 8-900. See if everything still holds together since the trans and clutch are only rated at 700 Yes the front bumper still fits on the car. https://cimg3.ibsrv.net/gimg/ls1tech...a2024488d6.png https://cimg5.ibsrv.net/gimg/ls1tech...c658a5d4b9.png https://cimg7.ibsrv.net/gimg/ls1tech...49a427c3eb.png https://cimg9.ibsrv.net/gimg/ls1tech...a7a89dd626.png https://cimg1.ibsrv.net/gimg/ls1tech...4fa7502217.png https://cimg2.ibsrv.net/gimg/ls1tech...2b4114a712.png https://cimg4.ibsrv.net/gimg/ls1tech...dbc0642379.png https://cimg7.ibsrv.net/gimg/ls1tech...878ee978f.jpeg https://cimg8.ibsrv.net/gimg/ls1tech...2c54f3494.jpeg Well where to begin! Got the engine and trans mated up https://cimg2.ibsrv.net/gimg/ls1tech...7e83d2c7f.jpeg Wrapped my manifolds https://cimg1.ibsrv.net/gimg/ls1tech...79f27155f.jpeg Everything installed ready to go back in the bay https://cimg0.ibsrv.net/gimg/ls1tech...1658d3468.jpeg I fabbed up some mounts for the accusump https://cimg9.ibsrv.net/gimg/ls1tech...103b35994.jpeg Then i got a hair up my ass and wanted a side exit exhaust https://cimg8.ibsrv.net/gimg/ls1tech...5659f0553.jpeg https://cimg7.ibsrv.net/gimg/ls1tech...700e9bd80.jpeg https://cimg6.ibsrv.net/gimg/ls1tech...1ff97afc8.jpeg https://cimg5.ibsrv.net/gimg/ls1tech...de60c4c1b.jpeg Can't have a clean engine going into a dirty bay, so i resprayed it https://cimg1.ibsrv.net/gimg/ls1tech...f4b03d40e.jpeg https://cimg9.ibsrv.net/gimg/ls1tech...c332609ac.jpeg Engine installed..... but with the side exit, this kinda forced me to redo the turbo kit...... This time around i wanted the turbo to where you can actually see it, so i clocked it about 15*...... hood still closes and bumper still fits https://cimg0.ibsrv.net/gimg/ls1tech...92def1617.jpeg The frame rail was going to give me issues with the exhaust..... i cut it and filled it back in with a pipe https://cimg8.ibsrv.net/gimg/ls1tech...4fc4292eb.jpeg https://cimg9.ibsrv.net/gimg/ls1tech...635334a03.jpeg I don't know how to do pie cuts, but they turned out damn good. https://cimg7.ibsrv.net/gimg/ls1tech...d527d4509.jpeg All mocked up https://cimg5.ibsrv.net/gimg/ls1tech...31de47179.jpeg ~finished turbo kit...... still need to add a wastegate to both banks, but that aint shit. https://cimg2.ibsrv.net/gimg/ls1tech...27288c985.jpeg Teardrop fender dump came out good too, perfect fit. https://cimg4.ibsrv.net/gimg/ls1tech...fb189e39e.jpeg Assembled! https://cimg1.ibsrv.net/gimg/ls1tech...b18d74211.jpeg Test fit a set of drag slicks i ordered....... looks good! https://cimg4.ibsrv.net/gimg/ls1tech...66835fb3f.jpeg https://cimg3.ibsrv.net/gimg/ls1tech...f6bda2d30.jpeg .....AAAAAnd thats about it. Hope you enjoy the build. |
All times are GMT -5. The time now is 01:15 PM. |
© 2024 MH Sub I, LLC dba Internet Brands