Price of a pre made wiring harness
#2
V8 Miata Fan
Join Date: Jan 2010
Location: Miami, Florida
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
McCully Racing Motors will sell you a modified Mustang harness for your FORD 5.0 conversion for $200 plus your harness.
http://www.mccullyracingmotors.com/i...ionharness.htm
http://www.mccullyracingmotors.com/i...ionharness.htm
#3
Moderator
For the Miata or for the LS1?
Ls1- many good ones on the internet
Miata- Your up a creek on that one. I picked my own harness clean. It took a long time, but was well worth it. I've thought about offering to do it on others, but the legalities are too great for this poor college kid
Ls1- many good ones on the internet
Miata- Your up a creek on that one. I picked my own harness clean. It took a long time, but was well worth it. I've thought about offering to do it on others, but the legalities are too great for this poor college kid
#5
Moderator
#6
V8 Miata Fan
I was going to go for the Painless kit as part of my LS1 MG project, but decided to check out how easy it would be to modify the GM parts. Short version: go with the GM one. It's really easy to do and very well documented. Took me about 3 hours from the time I sat down with the harness to basically having it ready to plug in.
#7
There are a few guys on LS1Tech who will mod a harness for you for cheaper, and a few of the ebay outfits that do it have a good rep at LS1Tech. I did my own like chpmnsws6 as some of the lengths of certain wires are unique to the Miata. It also depends on where you mount the PCM/ECU. I put mine in my '01 in the Pax footwell like the '90s.
Frank
Frank
#8
#9
Moderator
Not a bad price. If I were to do it for someone else, it'd easily run 150 or so with a clean harness provided. Though its not bad, it is time consuming to do it right, and a few things have to be redone to make it look decent.
That being said, mine is not up to par- don't put any tape on the wires till the harness is on the engine!!!!!!!!!
That being said, mine is not up to par- don't put any tape on the wires till the harness is on the engine!!!!!!!!!
#10
Not a bad price. If I were to do it for someone else, it'd easily run 150 or so with a clean harness provided. Though its not bad, it is time consuming to do it right, and a few things have to be redone to make it look decent.
That being said, mine is not up to par- don't put any tape on the wires till the harness is on the engine!!!!!!!!!
That being said, mine is not up to par- don't put any tape on the wires till the harness is on the engine!!!!!!!!!
Frank
#12
V8 Miata Fan
Join Date: Nov 2009
Location: Mountains of Arizona
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
Started from Scratch, I measured exactly where I wanted everything to be & go, designed a plug & play harness and drew it on the computer.
After stripping a used 2006 GTO harness I already had, reviewing plug / connector conditions / wiring, trying to figure what would be required to modify it to conform to my drawn design and what my time might be worth, had my design fabbed all NEW for about $650.00 Used HP Tuners GTO performance tune.
Ain't it 'posed ta be spel'd Meyater?
After stripping a used 2006 GTO harness I already had, reviewing plug / connector conditions / wiring, trying to figure what would be required to modify it to conform to my drawn design and what my time might be worth, had my design fabbed all NEW for about $650.00 Used HP Tuners GTO performance tune.
Ain't it 'posed ta be spel'd Meyater?
Last edited by LS2 V8 Miata; 03-19-2010 at 11:07 AM.
Thread
Thread Starter
Forum
Replies
Last Post
SupaDupaSteve
General Motors V8 Discussion
8
01-30-2015 10:45 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)